Read these instructions before using
your EntreeAir® Door Frame Fan™.
INSTALLATION INSTRUCTIONS
“WARNING - To Reduce The Risk Of
Fire, Electric Shock Or Injury To Persons,Observe The Following:”
1. Installation work and electrical wiring must be done by qualified person
(s) in accordance with all applicable codes and standards, including
fire-rated construction.
2. Sufficient air is needed for proper
combustion and exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the heating equipment
manufacturer’s guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and local
code authorities.
3. When cutting or drilling into wall or
ceiling, do not damage electrical wiring or other hidden utilities.
The EntreeAir® can be installed on the
frame of any doorway in either of the top corners.
The unit must be installed on the opposite side of the doorstop that the
door shuts against to permit closing the door. Follow instructions to
permanently install two screws in door frame (screws provided). The
EntreeAir® is installed over the screws by placing two keyhole slots over
the screw heads. Make sure the unit slips down over the screws and locks
into place. Multiple keyhole slots in the EntreeAir® Door Frame Fan™ are
provided to allow installation in the left or right corners of the doorway
and to allow for choice of direction of airflow. Observe the airflow
direction marked on the outside of the unit when installing. Securely attach
electrical cord to door frame with cord clips (clips provided).
CLEANING AND MAINTENANCE
Before cleaning the EntreeAir® always
disconnect the power cord from the outlet. Dust may be removed from the
exterior surfaces using a soft cloth, the round brush attachment of your
vacuum cleaner, or using a cloth that has been lightly moistened with water
and a mild non-abrasive detergent. Dust accumulation in the interior of the
EntreeAir® may be removed by using the round brush attachment of your vacuum
cleaner.
IMPORTANT WARNINGS
1) Unplug the EntreeAir® when not in use.
Turn the unit off before unplugging.
2) Do not operate the EntreeAir® with a damaged plug or cord, if the unit
malfunctions, becomes noisy when operating, has been dropped or otherwise
damaged, or if the housing is damaged or broken.
3) The EntreeAir® should never be exposed to moisture. Do not use the unit
in an open window, bathroom, or laundry area where it may come in contact
with water.
4) The EntreeAir® is designed for indoor use only.
5) Place the EntreeAir® and the electrical cord where it will not be tripped
over, and is out of the traffic pattern.
6) Never run the electrical cord under carpeting, baseboards, scatter rugs,
or hide it in any way.
7) Never insert any object or allow any object to enter the EntreeAir®
through the grills, as this may damage the unit or cause it to malfunction.
8) The motor of the EntreeAir® is equipped with a thermal fuse. Blocking
rotation of the fan or airflow may cause the motor to overheat. Should the
motor overheat and the fuse open, replacement of the motor is required.
9) Do not use the EntreeAir® near flammables such as gasoline, paint, or
natural gas.
10) The EntreeAir® is intended for use as described in the instructions
only. Other use may cause fire, electrical shock, damage to the unit, or
injury to persons and will void any warranty by the manufacturer.
11) The EntreeAir® has a polarized plug (one blade is wider than the other).
To reduce the risk of shock, this plug is intended to fit into a polarized
outlet only one way. If the plug does not fit into the outlet fully, reverse
the plug. If it still does not fit, contact a qualified electrician. DO NOT
attempt to defeat this safety feature.
12) If it is necessary to use an extension cord, use a heavy duty cord with
adequate wire size.
13) Pressure on the grills of the EntreeAir® may cause the fan impeller to
contact these grills and damage the unit.
14) Do not use strong detergents or flammable liquids to clean the
EntreeAir®.
15) The housing of your EntreeAir® is sealed at the factory. THERE ARE NO
SERVICEABLE PARTS INSIDE. Attempting to open the housing will expose you to
dangerous electricity, may cause fire, and will void any and all warranty.
16) Do not in any way block the air grills of the EntreeAir®.
INSTALLATION
INSTRUCTIONS
STEP 1 Cut out template.
Retain instructions for future reference.
STEP 2 Place either
narrow end of template against the top edge of
the door frame with the long edge against the doorstop.
STEP 3 Install one screw
at each center point. Allow screw to
project 1/4“. Position the unit securely on the screws.
